所有汽车都需要维护,这包括预定的冲洗to keep them working properly and running smoothly.
If you notice that your car is starting to overheat, or you notice that there’s no heat at all, something may be wrong. These are issues that should not be ignored, especially if you want your car to live a long and happy life, full of safe trips.
One way to ensure a healthy vehicle is by performing a routine heater core flush. If you don’t know what that is, then keep reading.
How Will I Know if I Need a Heater Core Flush?
有一些明显的迹象表明您的汽车需要加热器核心冲洗。加热器核心问题是独一无二的,尤其是因为这些潜在问题之一是泄漏到您的内部。
通常,当加热器核心问题出现时,这是由于冷却系统维护不良而造成的。您应该使用主人手册相应地冲洗和更换冷却液。这将有助于防止在狭窄的段落中堆积污垢,碎屑和锈蚀颗粒,最终导致堵塞和损坏。
Here are some of those telltale signs:
- 您的车似乎没有热身。It runs fine, the temperature gauge reads normal, and there are no other coolant system issues. Except for the lack of heat when you turn the heat on.
- There’s an unknown, sweet fragrance inside your car.那就是冷却液的气味,它可能会轻轻地喷入您的内部。这是一个预警信号。
- Your windows fog up.If your cooling is spraying for long enough, it could coat your windows. The residue is hard to clean off, and breathing in ethylene glycol is pretty bad for your health.
- Something’s leaking from under your dashboard.If you notice front carpet stains or dripping from under the dashboard, it’s coolant leaking into your car.
- Your engine is running hot.If this is the case, check your coolant level. If it’s running low and your temperature gauge is running high, you’re going to want to get to a mechanic.
If you’re not handy with mechanics, a heater core replacement cancost up to $950give or take. Which is why you’ll want to perform regular heater core flushes so that you can avoid the high heater core replacement cost. And breathing in poison.
分步加热器核心冲洗
A heater core flush is something that you can absolutely do yourself, even if you’re not mechanically inclined. Here’s what you’ll need to get started:
- A large bucket
- Clear tubing
- Gloves
- Pliers
- A screwdriver
- 花园软管
- An air compressor*
- A 3/4″ barb fitting adapter
- 破布
- safety glasses
- beplay体育app下地址
*An air compressor isn’t 100% obligatory, however, it is extremely helpful in loosening up any gunk before performing the flush.
If you’re using Irontite products for flushing, coating, and sealing, you’ll want to read the directions thoroughly before beginning this process.
现在,这是执行加热器核心冲洗的方法:
步骤1:找到加热器核心
First thing’s first. You’re going to want to find the heater core. It will be located on your car’s firewall. There will be an inlet and outlet hose, one that takes in the coolant and the other which pushes it back out. You’ll want to trace them back to the engine.
If you’re having trouble, refer to your owner’s manual.
Step 2: Disconnect the Heater Hoses
Once you’ve located the heater core and the hoses, disconnect them from the firewall. They’re bound by clamps, which will you’ll need pliers to squeeze or a screwdriver in order to loosen them.
Before you loosen them, make sure you set your large bucket underneath. Once you’ve removed the clamps and hoses, the coolant will begin to leak out. You’ll want to catch it all and dispose of it appropriately since it’s bad for the environment.
步骤3:施加压力
If you were able to get your hands on an air compressor, now is the time to use it. You’ll want to make sure that you hook it up to the outlet hose and seal it with a coupler or some duct tape.
This will enable you to build up pressure, loosening any gunk and tough clogs. You should “pressurize” the heater core for up to ten minutes for the best results. Once enough pressure has built up, you can shut off the compressor. (Caution: Too much pressure could cause damage. Most systems can easily withstand 20 to 40psi so to be safe you don’t want to exceed that much pressure.)
Before you remove your makeshift compressor hook up, let everything drain, keeping an eye on the bucket to see that it doesn’t overflow.
步骤4:用软管击中它
Once everything seems to have drained, you can remove the air compressor and attach the water hose using the same sealing method. Turn on the hose and let the flushing begin.
Once the water runs clear, you’re done flushing. Of course, you may want to repeat the entire process twice to ensure success. Once all the water has drained, you can use the air compressor to get rid of any excess water.
Step 5: Reconnect the Heater Hoses
Once you’ve successfully flushed and dried your heater core, you’ll want to reattach the hoses. It’s a good idea to have extra clamps on hand in case the old ones break. Make sure the hoses are back on properly and sealed with the clamps.
步骤5A:用Tholo-Flush冲洗整个冷却系统
At this point, it’s not a bad idea to take your efforts one step further and now do a full flush of your entire cooling system using a good quality chemical flush. Irontite Products Thoro-Flush is one of the most powerful of the available flush making it a good choice to get your entire cooling system all cleaned out. Here is a goodarticle on how to flush your car.
Step 6: Refill the Coolant
现在,您可以开始在加热器核心系统中重新填充冷却液。您可以通过卸下散热器盖并将冷却液混合物(最好是50/50的纯防冻剂和蒸馏水混合)来做到这一点。
这部分可以是一个过程,正如您将甲型肝炎e to run your car and let the coolant mixture flow through the system while alsoburping the coolant system。打bur将允许被困的空气被释放。系统中的空气会导致过热。
Don’t Forget Your Irontite Products
Older vehicles need a little more TLC, especially when flushing the system. Irontite offers some of the best flush and sealant products on the market. This includes Thoro-Flush, All-Weather Seal, and Ceramic Motor Seal. You can use them separately, or combined for the best results.
If you have any questions about Irontite’s products or need a recommendation of which to use, feel free tocontact usfor our professional opinion.